Schneider Electric · Charge controller
Conext MPPT 60 150 solar charge controller (XW-MPPT60-150, 865-1030 / 865-1030-1) Modbus register map
Default configuration
- Protocol
- Modbus TCP
- Port
- 502
- Unit ID
- 1
- Addressing
- 0-based
- Byte order
- Big endian
- Word order
- High word first
Register map
| Address | Count | Name | Type | Unit | Scale | Access |
|---|---|---|---|---|---|---|
| 0 | 8 | Device Name | Ascii | - | 1 | RW |
| 10 | 10 | FGA Number | Ascii | - | 1 | R |
| 20 | 10 | Unique ID Number | Ascii | - | 1 | R |
| 30 | 10 | Firmware Version | Ascii | - | 1 | R |
| 40 | 1 | Modbus Address | UInt16 | - | 1 | RW |
| 41 | 1 | Device Number | UInt16 | - | 1 | RW |
| 42 | 1 | System Instance | UInt16 | - | 1 | RW |
| 43 | 10 | Hardware Serial Number | Ascii | - | 1 | R |
| 53 | 1 | Configuration Status 0=Refreshing 1=Done | UInt16 | - | 1 | R |
| 54 | 2 | Configuration Refresh Counter | UInt32 | - | 1 | R |
| 64 | 1 | Device State See section 2 | UInt16 | - | 1 | R |
| 65 | 1 | Charger Enabled 0=Disabled 1=Enabled | UInt16 | - | 1 | R |
| 66 | 1 | Device Present 0=Inactive (all data invalid) 1=Active (data valid) | UInt16 | - | 1 | R |
| 67 | 1 | Charge Mode Status 0=Stand alone 1=Primary 2=Secondary | UInt16 | - | 1 | R |
| 68 | 1 | Active Faults Flag 0=No Active Faults 1=Has Active Faults | UInt16 | - | 1 | R |
| 69 | 1 | Active Warnings Flag 0=No Active Warnings 1=Has Active Warnings | UInt16 | - | 1 | R |
| 70 | 1 | Fault Bitmap 0 See section 3 | UInt16 | - | 1 | R |
| 71 | 1 | Fault Bitmap 1 See section 4 | UInt16 | - | 1 | R |
| 72 | 1 | Warning Bitmap 0 See section 5 | UInt16 | - | 1 | R |
| 73 | 1 | Charger Status See section 6 | UInt16 | - | 1 | R |
| 74 | 2 | Configuration Errors | UInt32 | - | 1 | R |
| 76 | 2 | Input DC Voltage | UInt32 | V | 0.001 | R |
| 78 | 2 | Input DC Current | UInt32 | A | 0.001 | R |
| 80 | 2 | Input DC Power | UInt32 | W | 1 | R |
| 86 | 1 | Battery Temperature | UInt16 | °C | 0.01 (offset -273) | R |
| 88 | 2 | Output DC Voltage | Int32 | V | 0.001 | R |
| 90 | 2 | Output DC Current | Int32 | A | 0.001 | R |
| 92 | 2 | Output DC Power | UInt32 | W | 1 | R |
| 94 | 1 | DC Power Output Percentage | UInt16 | % | 1 | R |
| 95 | 1 | Auxiliary Output Status See section 7 | UInt16 | - | 1 | R |
| 96 | 2 | Auxiliary Output Voltage | Int32 | V | 0.001 | R |
| 100 | 1 | Auxiliary Output On Reason See section 8 | UInt16 | - | 1 | R |
| 101 | 1 | Auxiliary Output Off Reason See section 9 | UInt16 | - | 1 | R |
| 102 | 2 | Energy From PV This Hour | UInt32 | kWh | 0.001 | R |
| 104 | 2 | PV Input Active This Hour | UInt32 | s | 1 | R |
| 106 | 2 | Energy From PV Today | UInt32 | kWh | 0.001 | R |
| 108 | 2 | PV Input Active Today | UInt32 | s | 1 | R |
| 110 | 2 | Energy From PV This Week | UInt32 | kWh | 0.001 | R |
| 112 | 2 | PV Input Active This Week | UInt32 | s | 1 | R |
| 114 | 2 | Energy From PV This Month | UInt32 | kWh | 0.001 | R |
| 116 | 2 | PV Input Active This Month | UInt32 | s | 1 | R |
| 118 | 2 | Energy From PV This Year | UInt32 | kWh | 0.001 | R |
| 120 | 2 | PV Input Active This Year | UInt32 | s | 1 | R |
| 122 | 2 | Energy From PV Lifetime | UInt32 | kWh | 0.001 | R |
| 124 | 2 | PV Input Active Lifetime | UInt32 | s | 1 | R |
| 126 | 2 | Energy To Battery This Hour | UInt32 | kWh | 0.001 | R |
| 128 | 2 | Battery Charge Active This Hour | UInt32 | s | 1 | R |
| 130 | 2 | Energy To Battery Today | UInt32 | kWh | 0.001 | R |
| 132 | 2 | Battery Charge Active Today | UInt32 | s | 1 | R |
| 134 | 2 | Energy To Battery This Week | UInt32 | kWh | 0.001 | R |
| 136 | 2 | Battery Charge Active This Week | UInt32 | s | 1 | R |
| 138 | 2 | Energy To Battery This Month | UInt32 | kWh | 0.001 | R |
| 140 | 2 | Battery Charge Active This Month | UInt32 | s | 1 | R |
| 142 | 2 | Energy To Battery This Year | UInt32 | kWh | 0.001 | R |
| 144 | 2 | Battery Charge Active This Year | UInt32 | s | 1 | R |
| 146 | 2 | Energy To Battery Lifetime | UInt32 | kWh | 0.001 | R |
| 148 | 2 | Battery Charge Active Lifetime | UInt32 | s | 1 | R |
| 160 | 1 | MPPT Enable 0=Disable 1=Enable | UInt16 | - | 1 | RW |
| 162 | 2 | MPPT Reference Voltage | UInt32 | V | 0.001 | RW |
| 165 | 1 | Battery Type See section 10 | UInt16 | - | 1 | RW |
| 166 | 2 | Nominal Battery Voltage See section 11 | UInt32 | V | 0.001 | RW |
| 168 | 1 | Battery Bank Capacity | UInt16 | Ah | 1 | RW |
| 169 | 1 | Battery Temperature Coefficient The map prints this row's scale as -1.0 and its unit as mV/deg C. | UInt16 | mV/deg C | -1 | RW |
| 170 | 1 | Force Charger State 1=Bulk 2=Float 3=No Float | UInt16 | - | 1 | RW |
| 171 | 1 | Reset 0=Reboot 2=Reset to Factory | UInt16 | - | 1 | RW |
| 172 | 1 | Operating Mode 2=Standby 3=Operating | UInt16 | - | 1 | RW |
| 173 | 1 | Clear See section 12 | UInt16 | - | 1 | RW |
| 174 | 2 | Equalize Voltage Set Point | UInt32 | V | 0.001 | RW |
| 176 | 2 | Bulk/Boost Voltage Set Point | UInt32 | V | 0.001 | RW |
| 178 | 2 | Float Voltage Set Point | UInt32 | V | 0.001 | RW |
| 180 | 2 | Recharge Voltage | UInt32 | V | 0.001 | RW |
| 182 | 2 | Absorption Voltage Set Point | UInt32 | V | 0.001 | RW |
| 184 | 1 | Absorption Time The map prints this row's scale as 0.0166 (one sixtieth), so the reading is in minutes. | UInt16 | min | 0.0166 | RW |
| 185 | 1 | Charge Cycle 1=3 Stage 2=2 Stage (No Float) | UInt16 | - | 1 | RW |
| 186 | 1 | Maximum Charge Rate | UInt16 | % | 1 | RW |
| 187 | 1 | Equalize Now 0=Disable 1=Enable | UInt16 | - | 1 | RW |
| 190 | 1 | Charge Mode See section 13 | UInt16 | - | 1 | RW |
| 191 | 1 | Default Battery Temperature 0=Cold 1=Warm 2=Hot | UInt16 | - | 1 | RW |
| 192 | 1 | Identify Enable 0=Disable 1=Enable | UInt16 | - | 1 | RW |
| 193 | 1 | Auxiliary Output Active Level 0=Active Low 1=Active High | UInt16 | - | 1 | RW |
| 194 | 2 | Auxiliary Output Voltage | UInt32 | V | 0.001 | RW |
| 196 | 1 | Manual Aux 0=Manual Off 1=Manual On 2=Automatic | UInt16 | - | 1 | RW |
| 198 | 1 | Auxiliary Output Trigger Source See section 14 | UInt16 | - | 1 | RW |
| 200 | 2 | Low Battery Voltage Trigger Set | UInt32 | V | 0.001 | RW |
| 202 | 1 | Low Battery Voltage Trigger Set Delay | UInt16 | s | 0.01 | RW |
| 204 | 2 | Low Battery Voltage Trigger Clear | UInt32 | V | 0.001 | RW |
| 206 | 1 | Low Battery Voltage Trigger Clear Delay | UInt16 | s | 0.01 | RW |
| 208 | 2 | High Battery Voltage Trigger Set | UInt32 | V | 0.001 | RW |
| 210 | 1 | High Battery Voltage Trigger Set Delay | UInt16 | s | 0.01 | RW |
| 212 | 2 | High Battery Voltage Trigger Clear | UInt32 | V | 0.001 | RW |
| 214 | 1 | High Battery Voltage Trigger Clear Delay | UInt16 | s | 0.01 | RW |
| 216 | 2 | High Array Voltage Trigger Set | UInt32 | V | 0.001 | RW |
| 218 | 1 | High Array Voltage Trigger Set Delay | UInt16 | s | 0.01 | RW |
| 220 | 2 | High Array Voltage Trigger Clear | UInt32 | V | 0.001 | RW |
| 222 | 1 | High Array Voltage Trigger Clear Delay | UInt16 | s | 0.01 | RW |
| 224 | 2 | Low Battery Temperature Trigger Set | UInt32 | °C | 0.001 (offset -273) | RW |
| 226 | 1 | Low Battery Temperature Trigger Set Delay | UInt16 | s | 0.01 | RW |
| 228 | 2 | Low Battery Temperature Trigger Clear | UInt32 | °C | 0.001 (offset -273) | RW |
| 230 | 1 | Low Battery Temperature Trigger Clear Delay | UInt16 | s | 0.01 | RW |
| 232 | 2 | High Battery Temperature Trigger Set | UInt32 | °C | 0.001 (offset -273) | RW |
| 234 | 1 | High Battery Temperature Trigger Set Delay | UInt16 | s | 0.01 | RW |
| 236 | 2 | High Battery Temperature Trigger Clear | UInt32 | °C | 0.001 (offset -273) | RW |
| 238 | 1 | High Battery Temperature Trigger Clear Delay | UInt16 | s | 0.01 | RW |
| 240 | 2 | High Heatsink Temperature Trigger Set | UInt32 | °C | 0.001 (offset -273) | RW |
| 242 | 1 | High Heatsink Temperature Trigger Set Delay | UInt16 | s | 0.01 | RW |
| 244 | 2 | High Heatsink Temperature Trigger Clear | UInt32 | °C | 0.001 (offset -273) | RW |
| 246 | 1 | High Heatsink Temperature Trigger Clear Delay | UInt16 | s | 0.01 | RW |
| 248 | 1 | Refresh Configuration Data 1=Refresh | UInt16 | - | 1 | RW |
| 249 | 1 | DC Input Association (PV) See section 15 | UInt16 | - | 1 | RW |
| 250 | 1 | DC Output Association (Battery) See section 16 | UInt16 | - | 1 | RW |
Read this device live with Modbus Connect, free for Windows, macOS and Linux
Related guides
Notes
The unit ID is a declared placeholder: the map prints the device's own 'Modbus Address' register but no factory value, and the Conext ComBox / Conext Gateway assigns the Modbus addresses itself (the ComBox Owner's Guide says it assigns them per device type at installation, valid 1-247, and lets you change or reset them), so read the address from the ComBox's Settings > Modbus Address List and use that. Port 502 is the ComBox's default Modbus TCP port as printed in its Owner's Guide. The map prints no function code; the ComBox writes its string registers with function code 0x10 (write multiple registers), so these rows are holding registers. Addresses are the map's own hexadecimal 'Modbus Address' column, stored as zero-based wire addresses. Rows whose type the map gives as str<nn> are seeded as Ascii rows of nn/2 registers. The MPPT 60 150 charge controller speaks Xanbus; these registers are the device map that the Conext ComBox or Conext Gateway presents over Modbus. Every register the map prints is in this file. The MPPT 80 600 (503-0252-01-01) has its own map and is not covered here. The printed hexadecimal numbers are the wire addresses (zero_based): in each of these maps the identity block is Device Name (str16) at 0x0000, FGA Number (str20) at 0x000A and Unique ID Number (str20) at 0x0014, so the ten registers of FGA Number run 0x000A-0x0013 into Unique ID Number at 0x0014, which only works if 0x0000 is register 0. The maps print no byte or word order for their uint32/sint32 rows, so HighFirst is the Modbus convention; if a two-register reading looks word-swapped, switch the device to LowFirst. Map: 'Modbus Map: Conext MPPT60 Device', 503-0248-01-01 Revision A.4, in Schneider's 'Conext Modbus Maps V4' pack.