INVT · VFD
Goodrive350-UL series high-performance VFD Modbus register map
Serial device: in Modbus Connect, choose “Add to existing device” and pick the serial (RTU) device you created on your COM port.
Default configuration
- Protocol
- Modbus RTU over RS-485
- Unit ID
- 1
- Addressing
- 0-based
- Byte order
- Big endian
- Word order
- High word first
- Baud rate
- 19200
- Parity
- Even
- Data bits
- 8
- Stop bits
- 1
To read this device over Modbus RTU in Modbus Connect:
- In Modbus Connect, add a serial (RTU) device on your COM port with the serial settings and unit ID shown above.
- Click Add to Modbus Connect (or open the downloaded JSON), choose “Add to existing device” and pick that serial device. Its registers, byte order and word order are added; the serial device keeps its own line settings.
The “Add device” tab creates a Modbus TCP device (IP address and port), so use it only when you reach this device through a Modbus RTU-to-TCP gateway set to the serial settings above.
Register map
| Address | Count | Name | Type | Unit | Scale | Access |
|---|---|---|---|---|---|---|
| 8192 | 1 | Communication-based control command 2000H. 0001H forward run, 0002H reverse run, 0003H forward jogging, 0004H reverse jogging, 0005H stop, 0006H coast to stop, 0007H fault reset, 0008H jogging to stop. Requires P00.01 = 2 (communication) and P00.02 = 0 (Modbus). | UInt16 | - | 1 | RW |
| 8193 | 1 | Communication-based frequency setting 2001H. 0 to Fmax, unit 0.01 Hz (fieldbus scale 100). | UInt16 | Hz | 0.01 | RW |
| 8194 | 1 | PID setting 2002H. 0-1000, 1000 corresponds to 100.0 %. Requires the PID reference source P09.00 to select Modbus communication. | UInt16 | % | 0.1 | RW |
| 8195 | 1 | PID feedback 2003H. 0-1000, 1000 corresponds to 100.0 %. | UInt16 | % | 0.1 | RW |
| 8196 | 1 | Torque setting 2004H. -3000 to +3000, 1000 corresponds to 100.0 % of the rated motor current. | Int16 | % | 0.1 | RW |
| 8197 | 1 | Upper limit of forward running frequency 2005H. 0 to Fmax, unit 0.01 Hz. | UInt16 | Hz | 0.01 | RW |
| 8198 | 1 | Upper limit of reverse running frequency 2006H. 0 to Fmax, unit 0.01 Hz. | UInt16 | Hz | 0.01 | RW |
| 8199 | 1 | Upper limit of electromotion torque 2007H. 0-3000, 1000 corresponds to 100.0 % of the rated VFD current. | UInt16 | % | 0.1 | RW |
| 8200 | 1 | Upper limit of brake torque 2008H. 0-3000, 1000 corresponds to 100.0 % of the rated motor current. | UInt16 | % | 0.1 | RW |
| 8201 | 1 | Special control command word 2009H. Bits 1-0 motor selection (00 motor 1 ... 11 motor 4), bit 2 torque control disabled, bit 3 power consumption reset, bit 4 pre-excitation, bit 5 DC brake. | UInt16 | - | 1 | RW |
| 8202 | 1 | Virtual input terminal command 200AH. 0x000-0x1FF. Virtual input terminal command bits; each bit acts as a digital input, for example a virtual forward-run or fault-reset terminal. | Hex | - | 1 | RW |
| 8203 | 1 | Virtual output terminal command 200BH. 0x00-0x0F. Virtual output terminal command bits (VDO1-VDO4), used when an output function is set to Modbus. | Hex | - | 1 | RW |
| 8204 | 1 | Voltage setting 200CH. 0-1000, 1000 corresponds to 100.0 % of the rated motor voltage; used with V/F separation. | UInt16 | % | 0.1 | RW |
| 8205 | 1 | AO output setting 1 200DH. -1000 to +1000, 1000 corresponds to 100.0 %. | Int16 | % | 0.1 | RW |
| 8206 | 1 | AO output setting 2 200EH. -1000 to +1000, 1000 corresponds to 100.0 %. | Int16 | % | 0.1 | RW |
| 8448 | 1 | VFD state word 1 2100H. 0001H forward running, 0002H reverse running, 0003H stopped, 0004H faulty, 0005H POFF, 0006H pre-excited. | UInt16 | - | 1 | R |
| 8449 | 1 | VFD state word 2 2101H. Bit 0 ready to run, bits 2-1 motor selection, bit 3 asynchronous/synchronous machine, bit 4 overload alarm, bits 6-5 control source (00 keypad, 01 terminal, 10 communication), bit 8 speed/torque control, bit 9 position control, bits 11-10 control mode. | UInt16 | - | 1 | R |
| 8450 | 1 | VFD fault code 2102H. Fault code of the active fault, see the fault-type description in the manual. | UInt16 | - | 1 | R |
| 8451 | 1 | VFD identification code 2103H. Device identification code. The device-code table gives 01H for the GD series in the 8 most significant bits and a0H for the GD350-UL vector VFD in the 8 least significant bits (01A0H), while the state-word table itself prints GD350-UL as 0109H; the two statements conflict in the manual and 01A0H is the one the encoding table defines. | Hex | - | 1 | R |
| 12288 | 1 | Running frequency 3000H. 0 to Fmax, unit 0.01 Hz. | UInt16 | Hz | 0.01 | R |
| 12289 | 1 | Set frequency 3001H. 0 to Fmax, unit 0.01 Hz. | UInt16 | Hz | 0.01 | R |
| 12290 | 1 | Bus voltage 3002H. 0.0-2000.0 V, unit 0.1 V. | UInt16 | V | 0.1 | R |
| 12291 | 1 | Output voltage 3003H. 0-1200 V, unit 1 V. | UInt16 | V | 1 | R |
| 12292 | 1 | Output current 3004H. 0.0-3000.0 A, unit 0.1 A. | UInt16 | A | 0.1 | R |
| 12293 | 1 | Rotating speed 3005H. 0-65535, unit 1 RPM. | UInt16 | rpm | 1 | R |
| 12294 | 1 | Output power 3006H. -300.0 to +300.0 %, unit 0.1 %. | Int16 | % | 0.1 | R |
| 12295 | 1 | Output torque 3007H. -250.0 to +250.0 %, unit 0.1 %. | Int16 | % | 0.1 | R |
| 12296 | 1 | Closed-loop setting 3008H. -100.0 to +100.0 %, unit 0.1 %. | Int16 | % | 0.1 | R |
| 12297 | 1 | Closed-loop feedback 3009H. -100.0 to +100.0 %, unit 0.1 %. | Int16 | % | 0.1 | R |
| 12298 | 1 | Input state 300AH. 000-1FF, the state of the digital inputs. | Hex | - | 1 | R |
| 12299 | 1 | Output state 300BH. 000-1FF, the state of the digital and relay outputs. | Hex | - | 1 | R |
| 12300 | 1 | Analog input 1 300CH. 0.00-10.00 V, unit 0.01 V. | UInt16 | V | 0.01 | R |
| 12301 | 1 | Analog input 2 300DH. 0.00-10.00 V, unit 0.01 V. | UInt16 | V | 0.01 | R |
| 12302 | 1 | Analog input 3 300EH. -10.00 to +10.00 V, unit 0.01 V. | Int16 | V | 0.01 | R |
| 12303 | 1 | Analog input 4 300FH. -10.00 to +10.00 V, unit 0.01 V. | Int16 | V | 0.01 | R |
| 12304 | 1 | High-speed pulse input 1 3010H. 0.00-50.00 kHz range, resolution 0.01 kHz; the manual prints the resolution suffix as 'unit: 0.01Hz' against this kHz range, which contradicts the range and is read as kHz. | UInt16 | kHz | 0.01 | R |
| 12305 | 1 | High-speed pulse input 2 3011H. 0.00-50.00 kHz range, resolution 0.01 kHz; the manual prints the resolution suffix as 'unit: 0.01Hz' against this kHz range, which contradicts the range and is read as kHz. | UInt16 | kHz | 0.01 | R |
| 12306 | 1 | Current step of multi-step speed 3012H. 0-15. | UInt16 | - | 1 | R |
| 12307 | 1 | External length 3013H. 0-65535. | UInt16 | - | 1 | R |
| 12308 | 1 | External count value 3014H. 0-65535. | UInt16 | - | 1 | R |
| 12309 | 1 | Torque setting (monitor) 3015H. -300.0 to +300.0 %, unit 0.1 %. | Int16 | % | 0.1 | R |
| 12310 | 1 | Identification code (monitor) 3016H. Device identification code. | Hex | - | 1 | R |
| 20480 | 1 | Fault code (monitor area) 5000H. Fault code as exposed in the monitor area. | UInt16 | - | 1 | R |
| 1 | 1 | P00.01 Running command channel Parameter P00.01 at 0001H: 0 keypad, 1 terminal, 2 communication. Set to 2 to let the drive accept run commands from Modbus. | UInt16 | - | 1 | RW |
| 2 | 1 | P00.02 Communication running command channel Parameter P00.02 at 0002H: 0 Modbus, 1 PROFIBUS/CANopen/DeviceNet, 2 Ethernet, 3 EtherCAT/PROFINET, 4 PLC card, 5 Bluetooth card. Set to 0 for Modbus control. | UInt16 | - | 1 | RW |
| 3 | 1 | P00.03 Maximum output frequency Parameter P00.03 at 0003H: unit 0.01 Hz, factory 60.00 Hz. The parameter list gives the range as P00.04-400.00 Hz and the detailed description as Max. (P00.04, 10.00)-630.00 Hz; the keypad figure prints a minimum and default of 50.00 Hz instead, which the parameter list contradicts. | UInt16 | Hz | 0.01 | RW |
| 4 | 1 | P00.04 Upper limit of running frequency Parameter P00.04 at 0004H: range P00.05-P00.03, unit 0.01 Hz, factory 60.00 Hz. | UInt16 | Hz | 0.01 | RW |
Read this device live with Modbus Connect, free for Windows, macOS and Linux
Related guides
Notes
Addresses are the manual's hexadecimal function-code addresses used unchanged on the wire: control and setting words 2000H-200EH, state words 2100H-2103H, monitors 3000H-3016H, fault code 5000H, and parameters addressed as 0xGGNN where GG is the group and NN the index after the dot (P00.01 = 0001H, P10.01 = 0A01H). Factory serial settings are P14.00 local address = 1, P14.01 baud rate = 4 (19200 bps) and P14.02 data bit check = 1 (even parity, 8 data bits, 1 stop bit). Communication control additionally requires P00.01 Running command channel = 2 (communication) and P00.02 Communication running command channel = 0 (Modbus); PID setpoints need P09.00 to select Modbus. Every parameter carries a fieldbus scale of 10^n where n is the number of decimals printed for it, so a value with two decimals is sent multiplied by 100. Writing a parameter with the most significant address byte changed from 00 to 80 writes RAM only instead of EEPROM (for example 8007H instead of 0007H for P00.07). Source: INVT 'Goodrive350-UL Series High-performance Multi-function VFD' operation manual, change history V1.1 (Nov 2019), chapter 9 'Communication protocol' - section 9.4.5.1 address representation rules (page 274), 9.4.5.2 control, state and monitor addresses (pages 275-277), 9.4.6 fieldbus scale (page 278), and the P14 group serial communication parameters (pages 200-202); PDF at https://www.invt.com/uploads/file1/20200628/GD350-UL%20Series%20VFD%20Manual.pdf.