WEG · VFD
CFW100 frequency inverter Modbus register map
Serial device: in Modbus Connect, choose “Add to existing device” and pick the serial (RTU) device you created on your COM port.
Default configuration
- Protocol
- Modbus RTU over RS-485
- Unit ID
- 1
- Addressing
- 0-based
- Byte order
- Big endian
- Word order
- High word first
- Baud rate
- 19200
- Parity
- Even
- Data bits
- 8
- Stop bits
- 1
To read this device over Modbus RTU in Modbus Connect:
- In Modbus Connect, add a serial (RTU) device on your COM port with the serial settings and unit ID shown above.
- Click Add to Modbus Connect (or open the downloaded JSON), choose “Add to existing device” and pick that serial device. Its registers, byte order and word order are added; the serial device keeps its own line settings.
The “Add device” tab creates a Modbus TCP device (IP address and port), so use it only when you reach this device through a Modbus RTU-to-TCP gateway set to the serial settings above.
Register map
| Address | Count | Name | Type | Unit | Scale | Access |
|---|---|---|---|---|---|---|
| 1 | 1 | Speed reference (P001) P001. Speed reference in the unit and scale defined by P208 (reference scale), P209 (engineering unit) and P210 (decimal places); no fixed factor applies because the unit is a setting. Read-only over Modbus, like every monitor. | UInt16 | - | 1 | R |
| 2 | 1 | Output speed (motor) (P002) P002. Speed imposed on the inverter output, at the same scale as P001 (P208/P209/P210), without the output compensations. | UInt16 | - | 1 | R |
| 3 | 1 | Motor current (P003) P003. Inverter output current in A rms; parameter range 0.0 to 10.0 A, i.e. one decimal place. | UInt16 | A | 0.1 | R |
| 4 | 1 | DC link voltage (P004) P004. DC link direct voltage in V; parameter range 0 to 524 V. | UInt16 | V | 1 | R |
| 5 | 1 | Output frequency (motor) (P005) P005. Frequency actually applied to the motor in Hz; parameter range 0.0 to 400.0 Hz, one decimal place. | UInt16 | Hz | 0.1 | R |
| 6 | 1 | Inverter status (P006) P006. 0 = ready, 1 = run, 2 = undervoltage, 3 = fault, 4 = self-tuning, 5 = configuration, 6 = DC braking, 7 = reserved, 8 = fire mode. | UInt16 | - | 1 | R |
| 7 | 1 | Output voltage (P007) P007. Line voltage at the inverter output in V; parameter range 0 to 240 V. | UInt16 | V | 1 | R |
| 9 | 1 | Motor torque (P009) P009. Torque developed by the motor in % of the rated torque; parameter range -200.0 to 200.0 %, one decimal place. | Int16 | % | 0.1 | R |
| 11 | 1 | Power factor (P011) P011. Power factor, the relation between real and total power absorbed by the motor; parameter range 0.00 to 1.00. | UInt16 | - | 0.01 | R |
| 12 | 1 | DI8 to DI1 status (P012) P012. Digital input status, bit 0 = DI1 through bit 7 = DI8; the activation level depends on P271 for each DIx. | Hex | - | 1 | R |
| 13 | 1 | DO3 to DO1 status (P013) P013. Digital output status, bit 0 = DO1, bit 1 = DO2, bit 2 = DO3. | Hex | - | 1 | R |
| 18 | 1 | AI1 value (P018) P018. Analog input AI1 in % of full scale after the offset action and gain (P230 to P245); parameter range -100.0 to 100.0 %. | Int16 | % | 0.1 | R |
| 100 | 1 | Acceleration time (P100) P100. Acceleration ramp time of the active ramp; parameter range 0.1 to 999.9 s, factory 5.0 s. | UInt16 | s | 0.1 | RW |
| 101 | 1 | Deceleration time (P101) P101. Deceleration ramp time of the active ramp; parameter range 0.1 to 999.9 s, factory 5.0 s. | UInt16 | s | 0.1 | RW |
| 680 | 1 | Logical status (P680) P680. Status word, bits: 1 run command, 2 fire mode, 5 second ramp, 6 configuration status, 7 alarm, 8 running, 9 enabled, 10 forward, 11 JOG, 12 remote, 13 undervoltage, 15 fault. | UInt16 | - | 1 | R |
| 681 | 1 | 13-bit speed (P681) P681. 13-bit speed with signal: 0 = 0 and 8192 (2000h) = the motor rated frequency P403, maximum 32767 = four times P403, so raw / 8192 is the fraction of P403 and the percentage shown is that fraction times 100. Negative values mean reverse. Read-only. | UInt16 | % of rated frequency | x / 8192 * 100 | R |
| 682 | 1 | Serial/USB control word (P682) P682. Serial interface control word; only writable over the serial interface. Bits: 0 run/stop, 1 general enable, 2 speed direction, 3 JOG, 4 LOC/REM, 5 second ramp, 7 fault reset. The drive must be programmed to be controlled via serial (P105 and P220 to P228). | UInt16 | - | 1 | RW |
| 683 | 1 | Serial speed reference (P683) P683. Serial speed reference in the same 13-bit scale as P681: 8192 (2000h) = rated frequency P403, so raw / 8192 is the fraction of P403 and the percentage shown is that fraction times 100. Negative values reverse the direction together with P682 bit 2. | Int16 | % of rated frequency | x / 8192 * 100 | RW |
| 308 | 1 | Serial address (P308) P308. Modbus RTU slave address, range 1 to 247, factory 1. | UInt16 | - | 1 | RW |
| 310 | 1 | Serial baud rate (P310) P310. 0 = 9600, 1 = 19200, 2 = 38400, 3 = 57600, 4 = 76800 bits/s; factory 1 (19200). | UInt16 | - | 1 | RW |
| 311 | 1 | Serial bytes configuration (P311) P311. 0 = 8 bits no parity 1 stop, 1 = 8 bits even parity 1 stop, 2 = 8 bits odd parity 1 stop, 3 = 8 bits no parity 2 stop, 4 = 8 bits even parity 2 stop, 5 = 8 bits odd parity 2 stop; factory 1. | UInt16 | - | 1 | RW |
| 312 | 1 | Serial protocol (P312) P312. 2 = Modbus RTU slave, 3 = BACnet, 5 = Modbus RTU master; factory 2. | UInt16 | - | 1 | RW |
Read this device live with Modbus Connect, free for Windows, macOS and Linux
Related guides
Notes
All CFW100 parameters are available as 16-bit holding registers and the data addressing uses offset zero, so the parameter number is the register address (P683 is address 683 = 02ABh). Factory serial settings are P308 = 1, P310 = 1 (19200 bit/s), P311 = 1 (8 bits, even parity, 1 stop bit) and P312 = 2 (Modbus RTU slave). To control the drive over the serial line, program P105 and P220 to P228 for the serial command and reference sources; P682 and P683 are only writable through the serial interface. Read-only parameters (P001 to P018, P680, P681) cannot be written. Sources: WEG 'CFW100 Modbus RTU User's Manual', document 10002909455/01 - section 5.2 Memory Map (parameter number equals register address), section 6 (function codes 03/04/06/16) and the P682/P683 control word and speed reference descriptions; PDF at https://static.weg.net/medias/downloadcenter/h77/hf0/WEG-cfw100-modbus-rtu-manual-10002909455-manual-english.pdf. Parameter ranges, scales and factory settings are from the WEG 'CFW100 Programming Manual', document 10008008405, chapter 0 Quick Reference of Parameters, chapter 11 READ parameters and section 12.2 SERIAL (P308 to P312); PDF at https://static.weg.net/medias/downloadcenter/ha6/he3/WEG-CFW100-programming-manual-10008008405-en.pdf.