Waveshare · Remote I/O
Modbus RTU IO 8CH (8 digital inputs / 8 digital outputs, RS485) Modbus register map
Serial device: in Modbus Connect, choose “Add to existing device” and pick the serial (RTU) device you created on your COM port.
Default configuration
- Protocol
- Modbus RTU over RS-485
- Unit ID
- 1
- Addressing
- 0-based
- Byte order
- Big endian
- Word order
- High word first
- Baud rate
- 9600
- Parity
- None
- Data bits
- 8
- Stop bits
- 1
To read this device over Modbus RTU in Modbus Connect:
- In Modbus Connect, add a serial (RTU) device on your COM port with the serial settings and unit ID shown above.
- Click Add to Modbus Connect (or open the downloaded JSON), choose “Add to existing device” and pick that serial device. Its registers, byte order and word order are added; the serial device keeps its own line settings.
The “Add device” tab creates a Modbus TCP device (IP address and port), so use it only when you reach this device through a Modbus RTU-to-TCP gateway set to the serial settings above.
Register map
| Address | Count | Name | Type | Unit | Scale | Access |
|---|---|---|---|---|---|---|
| 0 | 1 | Digital output 1 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
| 1 | 1 | Digital output 2 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
| 2 | 1 | Digital output 3 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
| 3 | 1 | Digital output 4 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
| 4 | 1 | Digital output 5 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
| 5 | 1 | Digital output 6 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
| 6 | 1 | Digital output 7 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
| 7 | 1 | Digital output 8 Output channel address 0x0000-0x0007: 0xFF00 = on, 0x0000 = off, 0x5500 = toggle (function 01/05/0F). | Binary | - | 1 | RW |
Read this device live with Modbus Connect, free for Windows, macOS and Linux
Related guides
Notes
Source: Waveshare wiki page https://www.waveshare.com/wiki/Modbus_RTU_IO_8CH, section 'Development Protocol V2' (function-code table, register-address table and worked commands), plus the product page https://www.waveshare.com/modbus-rtu-io-8ch.htm whose specification table prints 'Default communication format 9600, N, 8, 1', the baud-rate list and the input/output characteristics, and the vendor wiki page 'Modbus Series BootLoader Description' (restoring the default device parameters gives '9600 N 8 1' and device address 0x01). The wiki page's own specification table prints the same values - 'Default Communication Format 9600, N, 8, 1' and 'Set the device address range 1~255 (1 by default, corresponds to the hexadecimal value of 0x01)' - so the frame and the address are each cited twice. The control-mode registers are named in the page's Read/Write Control Mode sections (0 = normal, 1 = linkage, 2 = toggle, 3 = edge trigger). The register table prints addresses as 0x0000-0x0007, 1x0000-1x0007, 4x1000, 4x2000, 4x4000 and 4x8000; the seed stores those numbers unchanged and declares zero_based addressing. Only the readable / read-writable blocks are seeded: the write-only command coils 0x00FF (all outputs), 0x0200-0x0207 (flash on, interval in 100 ms steps) and 0x0400-0x0407 (flash off) are left out because the schema's coil area allows R and RW only. The four output control modes behind register 4x1000 are documented only as a 0-3 range, so they are stored without invented names. The input channels are passive or active 5-36 V inputs (NPN or PNP) with bidirectional optocoupler isolation; the outputs are open-drain, 5-40 V, 500 mA per channel.