KELLER Pressure · Pressure transmitter
X-Line pressure transmitters (series 33X / 35X / 36X / 39X, Class.Group 5.20 / 5.21 / 5.24) Modbus register map
Serial device: in Modbus Connect, choose “Add to existing device” and pick the serial (RTU) device you created on your COM port.
Default configuration
- Protocol
- Modbus RTU over RS-485
- Unit ID
- 1
- Addressing
- 0-based
- Byte order
- Big endian
- Word order
- High word first
- Baud rate
- 9600
- Parity
- None
- Data bits
- 8
- Stop bits
- 1
To read this device over Modbus RTU in Modbus Connect:
- In Modbus Connect, add a serial (RTU) device on your COM port with the serial settings and unit ID shown above.
- Click Add to Modbus Connect (or open the downloaded JSON), choose “Add to existing device” and pick that serial device. Its registers, byte order and word order are added; the serial device keeps its own line settings.
The “Add device” tab creates a Modbus TCP device (IP address and port), so use it only when you reach this device through a Modbus RTU-to-TCP gateway set to the serial settings above.
Register map
| Address | Count | Name | Type | Unit | Scale | Access |
|---|---|---|---|---|---|---|
| 0 | 2 | CH0, calculated value (float) Channel CH0 in the format selected by CFG_CH0 (0x0206), e.g. P1-P2, sqrt(P1) or |P1|. IEEE-754 big-endian: HWord at 0x0000, LWord at 0x0001. | Float32 | - | 1 | R |
| 2 | 2 | P1, pressure of sensor 1 (float) Pressure of pressure port P1. The document's worked frame reads 0x3F75 0xF07B at 0x0002 = 0.960701 bar. | Float32 | bar | 1 | R |
| 4 | 2 | P2, pressure of sensor 2 (float) Pressure of pressure port P2 (differential transmitters). The worked frame reads 0.961042 bar at 0x0004. | Float32 | bar | 1 | R |
| 6 | 2 | T, temperature (float) Temperature measured by the transmitter's own temperature sensor. | Float32 | °C | 1 | R |
| 8 | 2 | TOB1, temperature of sensor P1 (float) Temperature of the P1 pressure sensor. The worked frame reads 22.719 °C at 0x0008. | Float32 | °C | 1 | R |
| 10 | 2 | TOB2, temperature of sensor P2 (float) Temperature of the P2 pressure sensor. | Float32 | °C | 1 | R |
| 16 | 1 | CH0, calculated value (int16) Every value of this block is multiplied by 100 in the document, so the scale factor is 0.01. | Int16 | - | 0.01 | R |
| 17 | 1 | P1, pressure of sensor 1 (int16) Value x 0.01 bar. The block is limited to +/-327 bar; use the 32-bit block at 0x0022 for a wider range. | Int16 | bar | 0.01 | R |
| 18 | 1 | P2, pressure of sensor 2 (int16) Value x 0.01 bar. | Int16 | bar | 0.01 | R |
| 19 | 1 | T, temperature (int16) Value x 0.01 °C. | Int16 | °C | 0.01 | R |
| 20 | 1 | TOB1, temperature of sensor P1 (int16) Value x 0.01 °C. | Int16 | °C | 0.01 | R |
| 21 | 1 | TOB2, temperature of sensor P2 (int16) Value x 0.01 °C. | Int16 | °C | 0.01 | R |
| 32 | 2 | CH0, calculated value (int32) Unitless calculated channel; the device stores 10^-5 steps, so the scale factor is 0.00001. HWord at the lower address. | Int32 | - | 0.00001 | R |
| 34 | 2 | P1, pressure of sensor 1 (int32) The document stores this block in pascal (10^-5 bar); the seed converts to bar so it matches the other pressure rows. | Int32 | bar | 0.00001 | R |
| 36 | 2 | P2, pressure of sensor 2 (int32) Pascal block converted to bar (x 10^-5). | Int32 | bar | 0.00001 | R |
| 38 | 2 | T, temperature (int32) Value x 0.01 °C. | Int32 | °C | 0.01 | R |
| 40 | 2 | TOB1, temperature of sensor P1 (int32) Value x 0.01 °C. | Int32 | °C | 0.01 | R |
| 42 | 2 | TOB2, temperature of sensor P2 (int32) Value x 0.01 °C. | Int32 | °C | 0.01 | R |
| 512 | 1 | UART settings | UInt16 | - | 1 | RW |
| 513 | 1 | FILTER_bck, factory filter setting | UInt16 | - | 1 | R |
| 514 | 1 | Serial number, high bytes | UInt16 | - | 1 | R |
| 515 | 1 | Serial number, low bytes | UInt16 | - | 1 | R |
| 516 | 1 | CFG_P, active pressure channels | UInt16 | - | 1 | R |
| 517 | 1 | CFG_T, active temperature channels | UInt16 | - | 1 | R |
| 518 | 1 | CFG_CH0, calculated-channel mode | UInt16 | - | 1 | RW |
| 521 | 1 | P-Mode, sensor type and calibration | UInt16 | - | 1 | R |
| 522 | 1 | FILT_CTRL, filter control | UInt16 | - | 1 | RW |
| 523 | 1 | DAC_CTRL, analogue output control | UInt16 | - | 1 | R |
| 524 | 1 | STATUS, device status | UInt16 | - | 1 | R |
| 525 | 1 | DEV_ADDR, device (slave) address | UInt16 | - | 1 | RW |
| 526 | 1 | Class:Group, device class and group | UInt16 | - | 1 | R |
| 527 | 1 | Year:Week, firmware date | UInt16 | - | 1 | R |
| 529 | 1 | ConOn, conductivity power (CTD versions) | UInt16 | - | 1 | RW |
| 531 | 1 | ConRange, conductivity range (CTD versions) | UInt16 | - | 1 | RW |
| 532 | 1 | ConTempCompCoeff, conductivity temperature compensation | UInt16 | - | 1 | RW |
| 533 | 1 | ModbusInterFrameTime9k6 | UInt16 | - | 1 | RW |
| 534 | 1 | ModbusInterFrameTime115k2 | UInt16 | - | 1 | RW |
| 874 | 2 | Square-root threshold (coefficient 53) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Version 5.20 and 5.24. | Float32 | bar | 1 | RW |
| 896 | 2 | P1 offset (coefficient 64) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Default 0.0. | Float32 | bar | 1 | RW |
| 898 | 2 | P1 gain factor (coefficient 65) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Default 1.0. | Float32 | - | 1 | RW |
| 900 | 2 | P2 offset (coefficient 66) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Default 0.0. | Float32 | bar | 1 | RW |
| 902 | 2 | P2 gain factor (coefficient 67) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Default 1.0. | Float32 | - | 1 | RW |
| 904 | 2 | Analogue output offset (coefficient 68) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Version 5.20 and 5.24. | Float32 | bar | 1 | RW |
| 906 | 2 | Analogue output gain factor (coefficient 69) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Version 5.20 and 5.24. | Float32 | - | 1 | RW |
| 908 | 2 | CH0 offset (coefficient 70) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Default 0.0, version 5.20 and 5.24. | Float32 | - | 1 | RW |
| 910 | 2 | CH0 gain factor (coefficient 71) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Default 1.0, version 5.20 and 5.24. | Float32 | - | 1 | RW |
| 912 | 2 | T offset (coefficient 72) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Version 5.21 and 5.24. | Float32 | °C | 1 | RW |
| 916 | 2 | TOB1 offset (coefficient 74) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Version 5.21 and 5.24. | Float32 | °C | 1 | RW |
| 920 | 2 | TOB2 offset (coefficient 76) IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Writing coefficients needs function 16 with more than one register. Version 5.21 and 5.24. | Float32 | °C | 1 | RW |
| 928 | 2 | Minimum pressure of sensor P1 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | bar | 1 | R |
| 930 | 2 | Maximum pressure of sensor P1 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | bar | 1 | R |
| 932 | 2 | Minimum pressure of sensor P2 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | bar | 1 | R |
| 934 | 2 | Maximum pressure of sensor P2 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | bar | 1 | R |
| 936 | 2 | Minimum temperature of the temperature sensor IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | °C | 1 | R |
| 938 | 2 | Maximum temperature of the temperature sensor IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | °C | 1 | R |
| 940 | 2 | Minimum temperature of sensor P1 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | °C | 1 | R |
| 942 | 2 | Maximum temperature of sensor P1 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | °C | 1 | R |
| 944 | 2 | Minimum temperature of sensor P2 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | °C | 1 | R |
| 946 | 2 | Maximum temperature of sensor P2 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | °C | 1 | R |
| 948 | 2 | Minimum value of channel CH0 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | - | 1 | R |
| 950 | 2 | Maximum value of channel CH0 IEEE-754 float, two registers with the high word first; reading coefficients requires an even number of registers. Read-only measurement range. | Float32 | - | 1 | R |
Read this device live with Modbus Connect, free for Windows, macOS and Linux
Related guides
Notes
Source: KELLER Pressure AG 'Communication Protocol - X-Line Pressure Transmitters', version 3.8 (01/2026), vendor-hosted PDF at https://download.keller-pressure.com/api/download/muQjLg2dGMJAbgLYSAHreT/en/latest.pdf (SHA-256 276759928ad1ef8470f164d9c277f85dc87bb929990111a28beeac4d26fc4e31), chapters 2 (physical layer), 4.1 (Modbus basics), 4.4 (register map) and 4.4.3 (configuration range). The document covers the X-Line CLASS 5 devices: GROUP 20 (X1, software 5.20-XX.XX), GROUP 21 (X2, 5.21-XX.XX) and GROUP 24 (X2P, 5.24-XX.XX), i.e. the digital pressure transmitters of series 33X, 35X, 36X and 39X. Factory frame from chapter 4.1: Modbus RTU, 9600 baud, 8 data bits, no parity, 1 stop bit, slave address 1 (chapter 4.1 'Bus Addressing' and register 0x020D 'default 1'). Addressing: the register map prints the wire address - P1 sits at 0x0002 and is read as 0x0002 in the worked frames - so the seed is zero_based. Byte and word order: 32-bit values are IEEE-754 big-endian with the high word at the lower address (the worked frame at 0x0002 returns 0x3F75 0xF07B = 0.960701 bar), hence BigEndian + HighFirst. Not seeded: the 0x0100 float mirror block (its channel/unit column is printed one row out of line in the PDF and it only repeats 0x0000-0x000B), the conductivity coefficients (5.21 CTD versions only), the 0x0207/0x0208 interval/filter registers, the 0x0223 samples-per-second row, the 0x0250-0x0257 ASCII serial number, the analogue-signal (0x03B8-0x03BE), accuracy (0x03D0-0x03DA), conductivity (0x03E0-0x03EC) and samples-per-second (0x03F0-0x03FA) coefficient rows (with the 0x3000-0x301F, 0x3200-0x3217 and 0x4070-0x408F customer and filter tables) and the 0xFF00-0xFF1A write-only zero-point command list (those frames pack a fixed command byte rather than a plain value). P2 and TOB2 only exist on differential models; registers 0x0204/0x0205 report which channels are active. The int32 block is stored in pascal by the device and is scaled to bar here (x 10^-5).