GoodWe · Solar inverter
MT G2 / SMT / SDT G2 / MS / DNS / XS grid-connected string inverters (Modbus protocol V1.10, Customer Edition) Modbus register map
Serial device: in Modbus Connect, choose “Add to existing device” and pick the serial (RTU) device you created on your COM port.
Default configuration
- Protocol
- Modbus RTU over RS-485
- Unit ID
- 247
- Addressing
- 0-based
- Byte order
- Big endian
- Word order
- High word first
- Baud rate
- 9600
- Parity
- None
- Data bits
- 8
- Stop bits
- 1
To read this device over Modbus RTU in Modbus Connect:
- In Modbus Connect, add a serial (RTU) device on your COM port with the serial settings and unit ID shown above.
- Click Add to Modbus Connect (or open the downloaded JSON), choose “Add to existing device” and pick that serial device. Its registers, byte order and word order are added; the serial device keeps its own line settings.
The “Add device” tab creates a Modbus TCP device (IP address and port), so use it only when you reach this device through a Modbus RTU-to-TCP gateway set to the serial settings above.
Register map
| Address | Count | Name | Type | Unit | Scale | Access |
|---|---|---|---|---|---|---|
| 0 | 1 | Start-up voltage (60.0~600.0V) | UInt16 | V | 0.1 | RW |
| 1 | 1 | Reconnection time | UInt16 | s | 1 | RW |
| 2 | 1 | Grid Voltage Lower Limit [0.15*Vn,1*Vn] | UInt16 | V | 0.1 | RW |
| 3 | 1 | Grid Voltage Upper Limit [1*Vn,1.36*Vn] | UInt16 | V | 0.1 | RW |
| 4 | 1 | Grid Frequency Lower Limit | UInt16 | Hz | 0.01 | RW |
| 5 | 1 | Grid Frequency Upper Limit | UInt16 | Hz | 0.01 | RW |
| 16 | 1 | Device RTC Time Year/Month High Byte Year/Low Byte Month 13-99/1-12 | UInt16 | - | 1 | RW |
| 17 | 1 | Device RTC Time Day/Hour High Byte Day/Low Byte Hour 1-31/0-23 | UInt16 | - | 1 | RW |
| 18 | 1 | Device RTC Time Minute/Second High Byte Minute/Low Byte Second 0-59/0-59 | UInt16 | - | 1 | RW |
| 256 | 1 | Active power adjustment Corresponding to 0%-10 0% Active Power Note: Single-phase models only support writing and do not store data | UInt16 | % | 1 | RW |
| 257 | 1 | Power factor adjustment (PF reactive power) Note: Single-phase models only support writing; 1-20: PF =(Set value -1 00)/100, corresponding to lagging 0.99 to 0.8; 80-100: PF = Set value /10 0, corresponding to leading 0.80 to 1; | UInt16 | - | 1 | RW |
| 258 | 2 | Reactive power adjustment amount Note: Single-phase units are not supported. Setting range is [- 60%*Pn, 60%*Pn]。 | Int32 | var | 1 | RW |
| 262 | 1 | Inverter load increase/decrease (ARP limit) High byte: Load reduction or recovery amplitude (less than 0 indicates load reduction, greater than 0 indicates load increase,128 indicates full load recovery), unit is %. Low byte: Command ID | Int16 | % | 1 | W |
| 265 | 1 | Reactive power adjustment (percentage) (-60%~60%) , Note: Single-phase units are not supported. | Int16 | % | 1 | RW |
| 267 | 1 | Anti-backflow communication timeout Unit: seconds (Taiwan safety standard only) Note: Supported only by SMT | UInt16 | s | 1 | RW |
| 288 | 1 | Power On (Grid Connection Allowed Self-check) Register write 0 takes effect | UInt16 | - | 1 | W |
| 289 | 1 | Power Off (Grid Connection Not Allowed Self-check) Register write 0 takes effect | UInt16 | - | 1 | W |
| 290 | 1 | Restart Register write 0 takes effect | UInt16 | - | 1 | W |
| 291 | 1 | Grid-connected power limit switch 0- Off,1- On Note: Supported only by SDTG2/SMT | UInt16 | - | 1 | RW |
| 292 | 1 | Backflow upstream power percentage Note: Supported only by SDTG2/SMT | UInt16 | % | 1 | RW |
| 293 | 1 | Active power adjustment (MT) ARM 11 Version Import Note: Supported only by MT | UInt16 | % | 0.1 | RW |
| 312 | 1 | Shadow scan switch 0- Off,1- On | UInt16 | - | 1 | RW |
| 512 | 8 | Device serial number (16 ASCII characters) ASCII Code,16 characters | Ascii | - | 1 | R |
| 528 | 5 | Device model (10 ASCII characters) ASCII Code,10 characters | Ascii | - | 1 | R |
| 544 | 2 | Error code See Table 8-2 | UInt32 | - | 1 | R |
| 546 | 2 | Total energy fed to grid (E-Total) | UInt32 | kWh | 0.1 | R |
| 548 | 2 | Total feeding hours (h-Total) | UInt32 | h | 1 | R |
| 550 | 1 | Vpv1 / PV1 Input Voltage | UInt16 | V | 0.1 | R |
| 551 | 1 | Vpv2 / PV2 Input Voltage Note: Single MPPT Model Not Supported | UInt16 | V | 0.1 | R |
| 552 | 1 | Ipv1 / PV1 Input Current | UInt16 | A | 0.1 | R |
| 553 | 1 | Ipv2 / PV2 Input Current Note: Single MPPT Model Not Supported | UInt16 | A | 0.1 | R |
| 554 | 1 | Vac1 / L1 Phase Voltage | UInt16 | V | 0.1 | R |
| 555 | 1 | Vac2 / L2 Phase Voltage Note: Not supported by single-phase model | UInt16 | V | 0.1 | R |
| 556 | 1 | Vac3 / L3 Phase Voltage Note: Not supported by single-phase model | UInt16 | V | 0.1 | R |
| 557 | 1 | Iac1 / L1 Phase Current | UInt16 | A | 0.1 | R |
| 558 | 1 | Iac2 / L2 Phase Current Note: Not supported by single-phase model | UInt16 | A | 0.1 | R |
| 559 | 1 | Iac3 / L3 Phase Current Note: Not supported by single-phase model | UInt16 | A | 0.1 | R |
| 560 | 1 | Fac1 / L1 Phase Frequency | UInt16 | Hz | 0.01 | R |
| 561 | 1 | Fac2 / L2 Phase Frequency Note: Not supported by single-phase model | UInt16 | Hz | 0.01 | R |
| 562 | 1 | Fac3 / L3 Phase Frequency Note: Not supported by single-phase model | UInt16 | Hz | 0.01 | R |
| 563 | 1 | Inverter current output power (Pac) For Non-MT/SMT Models | UInt16 | W | 1 | R |
| 564 | 1 | Work mode 0:cWaitMode 1:cNormalMode 2:cFaultMode | UInt16 | - | 1 | R |
| 565 | 1 | Inverter internal temperature | UInt16 | °C | 0.1 | R |
| 566 | 1 | Daily energy generation (E-Day) | UInt16 | kWh | 0.1 | R |
| 768 | 1 | PV1 voltage (MT/SMT block) | UInt16 | V | 0.1 | R |
| 769 | 1 | PV2 voltage (MT/SMT block) | UInt16 | V | 0.1 | R |
| 770 | 1 | Ipv1 / PV1 Input Current | UInt16 | A | 0.1 | R |
| 771 | 1 | Ipv2 / PV2 Input Current | UInt16 | A | 0.1 | R |
| 772 | 1 | Vac1 / L1 Phase Voltage | UInt16 | V | 0.1 | R |
| 773 | 1 | Vac2 / L2 Phase Voltage | UInt16 | V | 0.1 | R |
| 774 | 1 | Vac3 / L3 Phase Voltage | UInt16 | V | 0.1 | R |
| 775 | 1 | Iac1 / L1 Phase Current | UInt16 | A | 0.1 | R |
| 776 | 1 | Iac2 / L2 Phase Current | UInt16 | A | 0.1 | R |
| 777 | 1 | Iac3 / L3 Phase Current | UInt16 | A | 0.1 | R |
| 778 | 1 | Fac1 / L1 Phase Frequency | UInt16 | Hz | 0.01 | R |
| 779 | 1 | Fac2 / L2 Phase Frequency | UInt16 | Hz | 0.01 | R |
| 780 | 1 | Fac3 / L3 Phase Frequency | UInt16 | Hz | 0.01 | R |
| 782 | 1 | Work mode (MT/SMT block) 0:cWaitMode 1:cNormalMode 2:cFaultMode | UInt16 | - | 1 | R |
| 783 | 1 | Inverter internal temperature (MT/SMT block) | UInt16 | °C | 0.1 | R |
| 784 | 2 | Error code See Table 8-2 | UInt32 | - | 1 | R |
| 786 | 2 | Total energy fed to grid (E-Total, MT/SMT block) | UInt32 | kWh | 0.1 | R |
| 788 | 2 | Total feeding hours (h-Total, MT/SMT block) | UInt32 | h | 1 | R |
| 790 | 1 | Firmware version | UInt16 | - | 1 | R |
| 791 | 1 | Warning code | UInt16 | - | 1 | R |
| 793 | 1 | Function status bits See Table 8-3 | UInt16 | - | 1 | R |
| 796 | 1 | DC bus voltage | UInt16 | V | 0.1 | R |
| 797 | 1 | DC bus neutral point voltage | UInt16 | V | 0.1 | R |
| 799 | 1 | Safety standards code Safety Standards Code | UInt16 | - | 1 | R |
| 800 | 1 | Daily energy generation (E-Day, MT/SMT block) | UInt16 | kWh | 0.1 | R |
| 804 | 1 | Vpv5 / PV5 Input Voltage Dedicated for SMT50 /60K Models | UInt16 | V | 0.1 | R |
| 805 | 1 | Ipv5 / PV5 Input Current Dedicated for SMT50 /60K Models | UInt16 | A | 0.1 | R |
| 806 | 1 | Vpv6 / PV6 Input Voltage Dedicated for SMT50 /60K Models | UInt16 | V | 0.1 | R |
| 807 | 1 | Ipv6 / PV6 Input Current Dedicated for SMT50 /60K Models | UInt16 | A | 0.1 | R |
| 814 | 1 | Power factor (SMT) Dedicated for SMT | Int16 | - | 0.001 | R |
| 827 | 1 | RTC year and month High Byte: Year; Low Byte : Month | UInt16 | - | 1 | R |
| 828 | 1 | RTC day and hour High Byte: Day; Low Byte : Hour | UInt16 | - | 1 | R |
| 829 | 1 | RTC minute and second High Byte: Minute; Low Byte : seconds | UInt16 | - | 1 | R |
| 830 | 1 | Manufacturer identification code For Hanergy | UInt16 | - | 1 | R |
| 831 | 1 | Wireless signal strength (RSSI) WiFi/GPRS Valid | UInt16 | % | 1 | R |
| 850 | 2 | AC power (Pac) | UInt32 | W | 1 | R |
| 852 | 1 | ARM software version | UInt16 | - | 1 | R |
| 853 | 1 | GPRS burn-in mode 0x00: Normal Mode 0x01: Aging Mode | UInt16 | - | 1 | R |
| 855 | 1 | Vpv3 / PV3 Input Voltage | UInt16 | V | 0.1 | R |
| 856 | 1 | Vpv4 / PV4 Input Voltage | UInt16 | V | 0.1 | R |
| 857 | 1 | Ipv3 / PV3 Input Current | UInt16 | A | 0.1 | R |
| 858 | 1 | Ipv4 / PV4 Input Current | UInt16 | A | 0.1 | R |
| 859 | 1 | Istr1/String 1 Electricity Current | UInt16 | A | 0.1 | R |
| 860 | 1 | Istr2/String 2 Electricity Current | UInt16 | A | 0.1 | R |
| 861 | 1 | Istr3/String 3 Electricity Current | UInt16 | A | 0.1 | R |
| 862 | 1 | Istr4/String 4 Electricity Current | UInt16 | A | 0.1 | R |
| 863 | 1 | Istr5/String 5 Electricity Current | UInt16 | A | 0.1 | R |
| 864 | 1 | Istr6/String 6 Electricity Current | UInt16 | A | 0.1 | R |
| 865 | 1 | Istr7/String7 Electric Current | UInt16 | A | 0.1 | R |
| 866 | 1 | Istr8/String8 Electric Current | UInt16 | A | 0.1 | R |
| 867 | 1 | Istr9/String9 Electric Current | UInt16 | A | 0.1 | R |
| 868 | 1 | Istr10/String 10 Current | UInt16 | A | 0.1 | R |
| 869 | 1 | Istr11/String 11 Current | UInt16 | A | 0.1 | R |
| 870 | 1 | Istr12/String 12 Current | UInt16 | A | 0.1 | R |
| 871 | 1 | Istr13/String 13 Current | UInt16 | A | 0.1 | R |
| 872 | 1 | Istr14/String 14 Current | UInt16 | A | 0.1 | R |
| 873 | 1 | Istr15/String 15 Current | UInt16 | A | 0.1 | R |
| 874 | 1 | Istr16/String 16 Current | UInt16 | A | 0.1 | R |
| 879 | 1 | PID and surge protection module status bits | UInt16 | - | 1 | R |
| 880 | 1 | Output control status Applicable to Japanese models:0- Uncontrolled, 1-Controlled Medium | UInt16 | - | 1 | R |
| 886 | 1 | Power factor (MT/SDT G2) Power Factor Note: MT/SDTG2 Dedicated | UInt16 | - | 0.001 | R |
| 893 | 2 | AC reactive power (MT/SMT/SDT G2) AC Reactive Power Note: MT/SMT/SDTG2 Dedicated | Int32 | kvar | 0.001 | R |
| 895 | 1 | Insulation impedance (ISO measured value) ISO Measured Value | UInt16 | kΩ | 1 | R |
| 896 | 1 | Leakage current Leakage Current Value | UInt16 | mA | 1 | R |
| 1000 | 2 | Current magnitude phase R | UInt32 | A | 0.1 | R |
| 1002 | 2 | Current magnitude phase S | UInt32 | A | 0.1 | R |
| 1004 | 2 | Current magnitude phase T | UInt32 | A | 0.1 | R |
| 1006 | 2 | Voltage magnitude phase R | UInt32 | V | 0.1 | R |
| 1008 | 2 | Voltage magnitude phase S | UInt32 | V | 0.1 | R |
| 1010 | 2 | Voltage magnitude phase T | UInt32 | V | 0.1 | R |
| 1012 | 2 | Three-phase active power | UInt32 | kW | 0.1 | R |
| 1014 | 2 | Three-phase reactive power | UInt32 | kW | 0.001 | R |
| 1016 | 2 | Three-phase power factor | Int32 | - | 0.001 | R |
| 1018 | 2 | Frequency (three-phase block) | UInt32 | Hz | 0.1 | R |
| 1020 | 2 | Status flag 1 Refer to Table 8-5 | UInt32 | - | 1 | R |
| 2000 | 1 | Power factor adjustment (MT) Note: MT supports | Int16 | - | 0.001 | RW |
| 2001 | 1 | Operation mode (power factor / Q(V) dispatch) Refer to Table 8-6 | UInt16 | - | 1 | RW |
| 2002 | 1 | Reactive power adjustment (MT dispatch) | Int16 | % | 0.1 | RW |
| 2003 | 1 | Active power adjustment (MT dispatch) | UInt16 | % | 0.1 | RW |
| 30115 | 1 | Grid AB line voltage | UInt16 | V | 0.1 | R |
| 30116 | 1 | Grid BC line voltage | UInt16 | V | 0.1 | R |
| 30117 | 1 | Grid CA line voltage | UInt16 | V | 0.1 | R |
| 30133 | 2 | AC apparent power | UInt32 | kVA | 0.001 | R |
| 30137 | 2 | Total input power | Int32 | kW | 0.001 | R |
| 32086 | 1 | Conversion efficiency | UInt16 | % | 0.01 | R |
| 37207 | 1 | Operation flag 7 Refer to Table 8-7 for details | UInt16 | - | 1 | R |
| 40491 | 1 | Taiwan safety standard Vpset Taiwan Safety Standards ( Un default 220 V) (1.05~1.1)*Un | UInt16 | V | 0.1 | RW |
| 40492 | 1 | Taiwan safety standard PF adjustment Taiwan safety standard dedicated (80-100) Note: Exclusive to SMT models use | UInt16 | % | 0.01 | RW |
| 40493 | 1 | Taiwan Safety Standards Reactive Power Adjustment Amount Taiwan safety standard dedicated (-60%~60%) Note: Exclusive to SMT models use | Int16 | % | 1 | RW |
| 40494 | 1 | Taiwan safety standard active power Adjustment value Taiwan safety standard dedicated (1,100) Note: Exclusive to SMT models use | UInt16 | % | 1 | RW |
| 40495 | 1 | Taiwan VPC Curve Switch Taiwan safety standard dedicated 0- Off, 1- On Note: Exclusive to SMT models use | UInt16 | - | 1 | RW |
| 42404 | 2 | Fixed active power derating Note: Exclusive to SMT models use | Int32 | W | 1 | RW |
| 42415 | 1 | Reactive power compensation (Q/Qn) Qn is 60% of Pn Note: Exclusive to SMT models use | Int16 | % of Qn | 0.1 | RW |
| 42439 | 1 | Active power dispatch enable 0: Accept third-party dispatch commands 1: Disable; do not accept thirdparty dispatch commands Note: Exclusive to SMT models use | UInt16 | - | 1 | RW |
Read this device live with Modbus Connect, free for Windows, macOS and Linux
Related guides
Notes
Source: GoodWe "Inverter MODBUS Communication Protocol - Grid-Connected MT G2/SMT/SDT G2/MS/DNS/XS Series (Customer Edition)", V1.10, 2025-05-09, 20 pp. GoodWe serves its library through a JS finder, so the file read is the distributor mirror https://www.nbservis.cz/GW_manualy/MTG2SMTSDTG2MSDNSXS_Modbus_V1_10_250509-en.pdf (SHA-256 4267498c618658f3bf17b18f9ee3d11c0ef6ca68522b8a104d88fe0eae54e813). Transport per the overview and section 4: Modbus RTU at 9600 bps; section 1 fixes each byte at 8 data bits with one start bit and one stop bit and prints no parity bit, so the None parity follows Modbus RTU default rather than a printed value; section 5 gives machine address 1-247 with factory default 247 (set with SolarGo or the display). Section 6: 03H reads and 10H writes, so every row is a holding register. Section 2 returns long integers high word first, hence HighFirst. Addresses are the document register numbers used as wire addresses: the table prints each number in decimal and hex (0x00, 0x0100) and section 9 writes register 256 by sending 0x0100, so the seed is zero-based. Units follow the document apart from library spellings (KWH/kWh, Hr/h, KW and kw/kW, kVar and Var/kvar, "degre eC"/degC, N/A/empty); 1014 keeps the document kW on the reactive-power row. Model coverage: 546-566 (0x222-0x236) apply only to non-MT models; 768-799 (0x300-0x31F) are the MT/SMT block; 563 is the non-MT/SMT output-power row; 804-807 are SMT 50/60K only; the 0x9E2x and 0xA5xx rows plus 886 are SMT-only. Register 42439 prints as "Power dispatch disable" although it is the active-power dispatch enable (0 = accept third-party dispatch, 1 = disable). Bit-field rows (544 error code, 793 function bits, 879 PID/surge bits, 1020 status flag 1, 37207 operation flag 7) are UInt16/UInt32 here and must be decoded with tables 8-2 to 8-7, which are not register lists and are not seeded. The GoodWe ET/EH/BT/BH storage map is a different document and is seeded separately as goodwe-et-eh.